*HTML is ON *UBB Code is ON Smilies Legend
Smilies Legend
If you have previously registered, but forgotten your password, click here.
T O P I C R E V I E WSpaceDustI have made my first set of homemade decals for my 1:96 scale Saturn V that I'm restoring and from reading the internet it seems every modeler uses a different laminate to seal them. What makes it worse is they all use and swear by different products. When you read about one good product then someone else says it's not any good. Some like sprays, some like brushing, and I've seen one recommendation to use a packing tape type product. After awhile it becomes very confusing and frustrating on what to use. Since there is a lot of good modelers here, can I have some suggestions on what you use as laminates and how it's used. (spray, brush on, others). I would like to have some suggestions on products before I screw up my project.Jay ChladekBefore I recommend something, what did you use to make the decals (paper? printer?). Are they stickers or waterslide?SpaceDustI used waterslide paper with a laser printer. Even though I read by using a laser printer they can be used as is, I've noticed that the print seems to come off easily.Jay ChladekJust grab yourself a can of Testors Model Master clear gloss on the standard Model Master paint rack (Testors Glosscote can also work, but I prefer the Model Master stuff, even if it costs slightly more) and spray a layer or two over it. Usually I do a light dusting layer, than a heavy layer before use. That should give it enough body for use and you decal solvent of choice will still work fine on it.Both clears are hobby strength lacquers. They are not enamels. There IS a Model Master high gloss clear enamel on the car rack, but don't use it as it is NOT the same stuff. These are not too hot unlike some clears and I use them exclusively for my own decals which I have done on laser photo copiers and with ALPS printers. The reason I recommend gloss instead of flat is in my experience, it is much easier to flat cover a home made decal after application than it is to gloss coat one if you happened to flat coat it first to seal it. Using a flat coat to seal the decal will make it fine for use, but it can absorb clearcoat like a sponge after it is on the model and STILL look flat.Since it is a laser decal, it will already be pretty durable. But I've found that the clear lacquer does give the decal a little more body. So it is less prone to wrinkling and distorting when applied. And of course the image also won't crack off as easily either. Just make sure you trim right up to the image before applying since the sheet is essentially one big decal.SpaceDustThanks Jay for your input and guidance, I really appreciate it and I'll give yours a try. I'm off to the hobby shop in the morning!Retro RocketI've always had the best results using three coats of Krylon Matte Finish. It's the only good product Krylon makes and it's very forgiving and always gives a nice finish. Also it's tougher than any laquer or enamel.divemaster"Future" through an airbrush. It also makes your model "lemony fresh"
When you read about one good product then someone else says it's not any good. Some like sprays, some like brushing, and I've seen one recommendation to use a packing tape type product. After awhile it becomes very confusing and frustrating on what to use.
Since there is a lot of good modelers here, can I have some suggestions on what you use as laminates and how it's used. (spray, brush on, others). I would like to have some suggestions on products before I screw up my project.
Both clears are hobby strength lacquers. They are not enamels. There IS a Model Master high gloss clear enamel on the car rack, but don't use it as it is NOT the same stuff. These are not too hot unlike some clears and I use them exclusively for my own decals which I have done on laser photo copiers and with ALPS printers. The reason I recommend gloss instead of flat is in my experience, it is much easier to flat cover a home made decal after application than it is to gloss coat one if you happened to flat coat it first to seal it. Using a flat coat to seal the decal will make it fine for use, but it can absorb clearcoat like a sponge after it is on the model and STILL look flat.
Since it is a laser decal, it will already be pretty durable. But I've found that the clear lacquer does give the decal a little more body. So it is less prone to wrinkling and distorting when applied. And of course the image also won't crack off as easily either. Just make sure you trim right up to the image before applying since the sheet is essentially one big decal.
Contact Us | The Source for Space History & Artifacts
Copyright 1999-2024 collectSPACE. All rights reserved.